diff --git a/branches/follower/wiz810mj/src/demo/WizDemo1/WizDemo1.pde b/branches/follower/wiz810mj/src/demo/WizDemo1/WizDemo1.pde
index 900666e..b7f9e46 100644
--- a/branches/follower/wiz810mj/src/demo/WizDemo1/WizDemo1.pde
+++ b/branches/follower/wiz810mj/src/demo/WizDemo1/WizDemo1.pde
@@ -34,8 +34,6 @@
     
      LGPL
      
-     (Although note spi_transfer comes from the Playground originally.)
-
   Version:
   
      20071106-0005
@@ -112,41 +110,6 @@ void setup () {
   //delay(10);
   Serial.println("Reset triggered...");
   
-  /*  
-  Serial.println("Configure device...");
-  
-  // default gateway
-  writeAddressValue(0x00, 0x01, 0xC0);
-  writeAddressValue(0x00, 0x02, 0xA8);
-  writeAddressValue(0x00, 0x03, 0x02);
-  writeAddressValue(0x00, 0x04, 0x65);
-  
-  // subnet mask
-  writeAddressValue(0x00, 0x05, 0xFF);
-  writeAddressValue(0x00, 0x06, 0xFF);
-  writeAddressValue(0x00, 0x07, 0xFF);
-  writeAddressValue(0x00, 0x08, 0x00);
-        
-  // source hardware address (MAC?)
-  writeAddressValue(0x00, 0x09, 0x00);
-  writeAddressValue(0x00, 0x0A, 0xDE);
-  writeAddressValue(0x00, 0x0B, 0xAD);
-  writeAddressValue(0x00, 0x0C, 0xBE);
-  writeAddressValue(0x00, 0x0D, 0xEF);
-  writeAddressValue(0x00, 0x0E, 0x00);
-
-  // source ip address
-  
-  writeAddressValue(0x00, 0x0F, 0xC0);
-  writeAddressValue(0x00, 0x10, 0xA8);
-  writeAddressValue(0x00, 0x11, 0x02);
-  writeAddressValue(0x00, 0x12, 0x69);
-  
-  
-  // Serial.println("SKIP: source ip address");
-  
-  Serial.println("End configure device...");
-  */  
 
   // driver chip init (Might be redundant with the above reset.)
   Serial.println("Call iinchip_init...");
@@ -185,51 +148,6 @@ void setup () {
   
 }
 
-byte readAddressValue(byte addressHiByte, byte addressLowByte) {
- // TODO: use a word for the address instead 
-  
- byte data = 0x00;
- 
- digitalWrite(PIN_SLAVE_SELECT, LOW); // Enable slave
- 
- // TODO: Check response values? e.g. 0x00, 0x01, 0x02
- spi_transfer(WIZNET_OPCODE_READ);
- spi_transfer(addressHiByte);
- spi_transfer(addressLowByte);
-
- data = spi_transfer(DUMMY_DATA);
-
- digitalWrite(PIN_SLAVE_SELECT, HIGH); // Disable slave
-  
- return data;
-}
-
-
-void writeAddressValue(byte addressHiByte, byte addressLowByte, byte targetValue) {
- // TODO: use a word for the address instead 
-  
- digitalWrite(PIN_SLAVE_SELECT, LOW); // Enable slave
- 
- // TODO: Check response values? e.g. 0x00, 0x01, 0x02
- spi_transfer(WIZNET_OPCODE_WRITE);
- spi_transfer(addressHiByte);
- spi_transfer(addressLowByte);
-
- spi_transfer(targetValue);
-
- digitalWrite(PIN_SLAVE_SELECT, HIGH); // Disable slave  
-}
-
-// From Playground
-char spi_transfer(volatile char data)
-{
-  SPDR = data;                    // Start the transmission
-  while (!(SPSR & (1<<SPIF)))     // Wait for the end of the transmission
-  {
-  };
-  return SPDR;                    // return the received byte
-}
-
 void sendPrompt(uint8_t *buffer) { // {Socket targetSocket, ) {
   buffer[0] = 'w';
   buffer[1] = '0';