ADDED - Driver: function routines for using hardware checksum capabilities (enc28j60[conf].cpp/h, nic.h).

MODIF - ICMP: Switched to hardware checksum routines.
MODIF - Main: Better output of ip config when in debug mode.
ISSUE - Only the new checksum should be written back to the memory, not the whole packet.

git-svn-id: svn+ssh://oldsvn/home/mlalondesvn/svn/Ethduino@5 b05466c9-153a-0410-ad00-ea1d4d8a27b5

enc28j60.cpp

@@ -114,6 +114,15 @@ void nicReboot(void)
 	enc28j60Reboot();
 }
 
+uint16_t nicGetChecksum(uint8_t* packet, uint16_t len)
+{
+#ifdef ENC28J60_CHECKSUM_ENABLED
+	enc28j60getChecksum(packet, len);
+#else
+	return 0x0000;
+#endif
+}
+
 void enc28j60Reboot(void)
 {
 #ifndef ENC28J60_HARD_RESET_DISABLED
@@ -215,6 +224,68 @@ void enc28j60ReadBuffer(uint16_t len, uint8_t* data)
 	sbi(ENC28J60_CONTROL_PORT, ENC28J60_CONTROL_CS);
 }
 
+
+uint16_t enc28j60getChecksum(uint8_t* packet, uint16_t len)
+//void enc28j60PacketSend(uint16_t len, uint8_t* packet)
+{
+	// Errata workaround #10 Transmit Logic
+	if (enc28j60Read(EIR) & EIR_TXERIF)
+	{
+		enc28j60WriteOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_TXRST);
+		enc28j60WriteOp(ENC28J60_BIT_FIELD_CLR, ECON1, ECON1_TXRST);
+		enc28j60WriteOp(ENC28J60_BIT_FIELD_CLR, EIR, EIR_TXERIF);
+	}
+
+	// Set the write pointer to start of transmit buffer area
+	enc28j60Write(EWRPTL, TXSTART_INIT);
+	enc28j60Write(EWRPTH, TXSTART_INIT>>8);
+
+	// Set the TXND pointer to correspond to the packet size given
+	enc28j60Write(ETXNDL, (TXSTART_INIT+len));
+	enc28j60Write(ETXNDH, (TXSTART_INIT+len)>>8);
+
+	// write per-packet control byte
+	enc28j60WriteOp(ENC28J60_WRITE_BUF_MEM, 0, 0x00);
+	
+	// copy the packet into the transmit buffer
+	enc28j60WriteBuffer(len, packet);
+	
+	// return the calculated checksum
+	return enc28j60doHardwareChecksum(len);
+}
+
+uint16_t enc28j60doHardwareChecksum(uint16_t len)
+{
+	// Set EDMASTL to the beggining of the used memory
+	enc28j60Write(EDMASTL, TXSTART_INIT);
+	enc28j60Write(EDMASTH, TXSTART_INIT>>8);
+
+	// Set EDMAND to the end of the memory used
+	enc28j60Write(EDMANDL, (TXSTART_INIT+len));
+	enc28j60Write(EDMANDH, (TXSTART_INIT+len)>>8);
+
+	// Set EDMADST to the beggining of the DMA buffer
+	enc28j60Write(EDMADSTL, TXSTART_INIT);
+	enc28j60Write(EDMADSTH, TXSTART_INIT>>8);
+	
+	// Enable DMA copy mode
+	enc28j60WriteOp(ENC28J60_BIT_FIELD_CLR, ECON1, ECON1_CSUMEN);
+	enc28j60WriteOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_DMAST);
+	
+	// Wait for the DMA copy to complete
+	while(!(enc28j60Read(EIR) & EIR_DMAIF));
+	
+	// Start the checksum calculation
+	enc28j60WriteOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_CSUMEN);
+	enc28j60WriteOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_DMAST);
+	
+	// Wait for the checksum calculation to complete
+	while(!(enc28j60Read(ECON1) & ~ECON1_DMAST && enc28j60Read(EIR) & EIR_DMAIF));
+	
+	// Read back and return the calculated checksum
+	return (uint16_t)(enc28j60Read(EDMACSL) | (uint16_t)enc28j60Read(EDMACSH)<<8);
+}
+
 void enc28j60WriteBuffer(uint16_t len, uint8_t* data)
 {
 	// assert CS

enc28j60.h

@@ -301,6 +301,9 @@ uint16_t enc28j60PhyRead(uint8_t address);
 //! write a PHY register
 void enc28j60PhyWrite(uint8_t address, uint16_t data);
 
+uint16_t enc28j60doHardwareChecksum(uint16_t len);
+uint16_t enc28j60getChecksum(uint8_t* packet, uint16_t len);
+
 //! initialize the ethernet interface for transmit/receive
 /// \return -1 if there was a problem initializing the NIC, otherwise the value is undefined
 char enc28j60Init(void);

enc28j60conf.h

@@ -67,6 +67,9 @@
 #define ENC28J60_PACKET_FILTER_ENABLED	/* Unimplemented */
 
 #define ENC28J60_LAMPS_MODE			0x3476 /* Default (with Errata #9 correction) applied if this is undefied */
+
+#define ENC28J60_CHECKSUM_ENABLED
+
 /**
  * Lamps reference
  *	0x3D56	# Default full duplex: LEDA: Display link status and transmit/receive activity LEDB: Display duplex status

icmp.cpp

@@ -26,6 +26,10 @@
 #include "HardwareSerial.h"
 #endif
 
+#ifdef NET_CHECKSUM_DEBUG
+#include "enc28j60.h"
+#endif
+
 // functions
 void icmpInit(void)
 {
@@ -48,36 +52,27 @@ void icmpIpIn(icmpip_hdr* packet)
 
 void icmpEchoRequest(icmpip_hdr* packet)
 {
-	uint32_t tempIp, tempId;
+	uint32_t tempIp;
+	uint16_t tempId;
 	
 	// change type to reply
 	packet->icmp.type = ICMP_TYPE_ECHOREPLY;
 	
 	// recalculate checksum
 	packet->icmp.icmpchksum = 0x0000;
-	packet->icmp.icmpchksum = ipChecksum((netIpHeader*)&packet->icmp, htons(packet->ip.len)-sizeof(netIpHeader));
+	packet->icmp.icmpchksum	= nicGetChecksum((uint8_t*)&packet->icmp, htons(packet->ip.len)-IP_HEADER_LEN);
 	
-#ifdef NET_CHECKSUM_DEBUG
+	#ifdef NET_CHECKSUM_DEBUG
 		SPrintln(" ");
-	SPrint("ICMP Checksum: 0x");
+		SPrint("Hardware Checksum: 0x");
-	Serial.print((uint16_t)htons(packet->icmp.icmpchksum), HEX);
-	SPrint(" 0x");
 		Serial.println((uint16_t)HTONS(packet->icmp.icmpchksum), HEX);
-#endif
+	#endif
 	
 	// return to sender
 	tempIp = packet->ip.destipaddr;
 	packet->ip.destipaddr = packet->ip.srcipaddr;
 	packet->ip.srcipaddr = tempIp;
 	
-	// Set the proper transaction id
-	
-	tempId = packet->ip.ipid;
-	packet->ip.ipid = tempId;
-	
-	tempId = packet->icmp.id;
-	packet->icmp.id = tempId;
-	
 	// add ethernet routing
 	arpIpOut((struct netEthIpHeader*)(((u08*)packet)-ETH_HEADER_LEN), 0);
 	
@@ -88,7 +83,7 @@ void icmpEchoRequest(icmpip_hdr* packet)
 	#endif
 	
 	// send it (packet->ip.len+ETH_HEADER_LEN
-	nicSend(htons(packet->ip.len)+ETH_HEADER_LEN, (((u08*)packet)-ETH_HEADER_LEN));
+	nicSend(htons(packet->ip.len)+ETH_HEADER_LEN, (((uint8_t*)packet)-ETH_HEADER_LEN));
 }
 
 #ifdef ICMP_DEBUG_PRINT

icmp.h

@@ -31,7 +31,7 @@
 
 #include "net.h"
 
-#define ICMP_DEBUG_PRINT
+// #define ICMP_DEBUG_PRINT
 
 //! Initialize ICMP protocol library.
 void icmpInit(void);

main.pde

@@ -5,7 +5,6 @@
 **/
 
 #include "main.h"
-
 /**
  * Network support
 **/
@@ -21,6 +20,8 @@
 #include "ip.h"
 #include "icmp.h"
 
+#define PrintIP(ip) netPrintIPAddr(ip); SPrintln(" ")
+
 struct netEthAddr myEthAddress;
 
 // prototypes
@@ -112,10 +113,12 @@ void serviceLocal(void)
 				sbi(ENC28J60_CONTROL_PORT, ENC28J60_CONTROL_CS);
 			break;
 			*/
-#if defined(NET_DEBUG) || defined(NIC_DEBUG)
+#if defined(ARP_DEBUG_PRINT)
 			case 'a' :
 				arpPrintTable();
 			break;
+#endif
+#if defined(NET_DEBUG) || defined(NIC_DEBUG)
 			case 'd':
 				nicRegDump();
 			break;
@@ -144,11 +147,13 @@ void serviceLocal(void)
 			case 'c':
 				SPrintln("IP Configs");
 				SPrint("IP:");
-				Serial.println(ipGetConfig()->ip);
+				PrintIP(ipGetConfig()->ip);
 				SPrint("Gateway:");
-				Serial.println(ipGetConfig()->gateway);
+				PrintIP(ipGetConfig()->gateway);
 				SPrint("Netmask:");
-				Serial.println(ipGetConfig()->netmask);
+				PrintIP(ipGetConfig()->netmask);
+				//SPrint("MAC:");
+				//netPrintEthAddr(netEthAddr);
 			break;
 			/*
 			case 'x':

net.cpp

@@ -30,13 +30,18 @@ uint32_t htonl(uint32_t val)
 	return (htons(val>>16) | (uint32_t)htons(val&0x0000FFFF)<<16);
 }
 
-static uint16_t generateChecksum(uint16_t sum, netIpHeader *data, uint16_t len)
+uint16_t generateChecksum(uint16_t sum, netIpHeader *data, uint16_t len)
 {
 	uint16_t t;
 
 	uint32_t *dataptr;
 	uint32_t *last_byte;
 
+#ifdef NET_CHECKSUM_DEBUG
+	SPrint("Length for chksum func: ");
+	Serial.println((long int)len, HEX);
+#endif
+	
 	dataptr		= (uint32_t *) data;
 	last_byte	= (uint32_t *) data + len - 1;
 

net.h

@@ -29,7 +29,7 @@
 
 
 // #define NET_DEBUG 7
-//#define NET_CHECKSUM_DEBUG
+// #define NET_CHECKSUM_DEBUG
 
 #include "avrlibdefs.h"
 #include "avrlibtypes.h"
@@ -198,7 +198,7 @@ uint16_t ipChecksum(netIpHeader *data, uint16_t len);
 //! Calculate IP Header checksum from data.
 uint16_t netChecksum(netIpHeader *data, uint16_t len);
 
-static uint16_t generateChecksum(uint16_t sum, netIpHeader *data, uint16_t len);
+uint16_t generateChecksum(uint16_t sum, netIpHeader *data, uint16_t len);
 
 //! Print Ethernet address in XX:XX:XX:XX:XX:XX format.
 void netPrintEthAddr(struct netEthAddr* ethaddr);

netstack.h

@@ -44,7 +44,7 @@
 #include "ip.h"
 #include "nic.h"
 
-// #define NETSTACK_DEBUG
+//#define NETSTACK_DEBUG
 
 /// NET_BUFFERSIZE is the common receive/process/transmit buffer.
 /// - You may override the default NET_BUFFERSIZE by defining an alternate value in global.h.

nic.h

@@ -27,6 +27,7 @@
 #ifndef NIC_H
 #define NIC_H
 
+#include "net.h"
 // #define NIC_DEBUG
 
 #include <inttypes.h>
@@ -81,5 +82,8 @@ void nicSoftReset(void);
 //! PHY Chip reboot
 void nicReboot(void);
 
+//! PHY Chip hardware checksum, if available
+uint16_t nicGetChecksum(uint8_t* packet, uint16_t len);
+
 #endif
 //@}